manualshive.com logo in svg

A-Neu Video ANI-4KANA, Instruction Manual

Share
Download
A-Neu Video ANI-4KANA Instruction Manual Download Page 13

11

REMOTE CONTROL

q

 ANALYZER/PATTERN: 

Press to switch between 

Analyzer Mode and Pattern Mode.

w

 EDID:

 Press repeatedly to switch between the 

available EDIDs for the HDMI input.

e

 COLOR SPACE:

 Press repeatedly to switch 

between the available color space formats (RGB, 

YCbCr 4:4:4, YCbCr 4:2:2 and YCbCr 4:2:0).

r

 HDCP SW.:

 

Press to switch between supported 

HDCP versions or to disable HDCP.

t

 FORMAT: 

Press to switch between DVI and HDMI 

output formats.

y

 VGA~4K6G:

 Press to directly select the output 

resolution.

u

 OUTPUT ON:

 Press to enable video output.

i

 OUTPUT OFF:

 Press to disable video output.

o

 T-/T+:

 Press

 (+/-) 

to select a new output resolution timing. Within the OSD menu, press 

to adjust selections.

P+/P-:

 Press

 (+/-) 

to change the current test pattern. Within the OSD menu, press to move 

up and down.

OK:

 

After selecting a pattern, press and hold for 2 seconds to switch to alternate variations 

of the pattern. Within the OSD menu, press to confirm selections.

a

 MENU:

 Press to enter the OSD menu.

s

 EXIT:

 Press to exit the OSD or cancel the selection.

d

 SOURCE*:

 Press to display source signal information on the OSD.

 

VIDEO T*.:

 Press to display video analysis details on the OSD. 

AUDIO T*.:

 Press to display audio analysis details on the OSD.

PACKET*:

 Press to display the HDMI input’s packet analysis info.

HOTPLUG*:

 Press to force an RX hot-plug event on the input port.

SINK**:

 Press to display HDMI output detection/information on the OSD.

Summary of Contents for ANI-4KANA





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands