background image

15

16

4.  Do not use detergents which contain lanolin or other oils since they may soften and/or distort the facepiece lens. 
5.  Rinse in clean water. Water temperature should not exceed 120°F (49°C). 
6.  Dry in uncontaminated ambient air. If using forced air, do not exceed 120°F (49°C). 
7.  Disinfect facepiece by soaking in a solution of quaternary ammonia disinfectant or sodium hypochloride 

(1 oz [30 ML] household bleach in 2 gallons [7.5 L] of water), or other disinfectant. Rinse in fresh, warm water and air 

dry in non-contaminated atmosphere.

Inspecting the Facepiece

This respirator must be inspected before each use to ensure it is in good operating condition. Any damaged or defective 

parts must be replaced before use. The following procedure is suggested: 
1.  Check the facepiece and breathing tube for cracks, tears and dirt. Be certain the facepiece, especially the faceseal area, 

is not distorted. The material must be pliable, not stiff.

2.  Make sure that head straps are intact and have good elasticity.
3.  Examine all plastic parts for signs of cracking or fatiguing.
4.  Remove the exhalation valve cover and examine the valve and valve seat for signs of dirt, distortion, cracking or tearing. 

Snap the exhalation valve cover back into place. 

5.  Examine the bayonet lugs for signs of unusual wear. Examine the orange gasket for signs of wear. 
6.  Repair or replace parts only with the 3M components approved for this system. 

Inspecting the Air Control Valves

The regulators and connectors have no moving parts except for the airfl ow adjustment knob on the 3M™ Air Regulator 

SA-1009, so there is very little that will require maintenance. If the air from the compressor or pump meets regulatory 

requirements, the spring check valve inside of these regulators and connectors should continue to operate normally for a 

long period of time. It is recommended that you follow these maintenance guidelines for the 3M air regulator SA-1009 and 

3M™ Low Pressure Connector SA-1029:
1.  Waist belt (GVP-127) - The waist belt may be hand laundered with mild detergent, a clean water rinse and air dried.
2.  Air regulator (SA-1009) and low pressure connector (SA-1029) – Clean the exterior of the valve or connector as needed 

by wiping down with a damp cloth. Blow clean with compressed air.

 CAUTION

Do not immerse the air regulator or low pressure connector in water; doing so may saturate the foam spring valve with 

water. Failure to dry the foam may result in the growth of mold or mildew.

Storage

The respirator should be placed in a clean container or bag and stored at ambient temperature in a dry, uncontaminated area 

protected from bright sunlight.

TROUBLESHOOTING 

Use the table below to help identify possible causes and corrective action for problems you may experience.

Problem

Possible Cause

Corrective Action

You smell or taste contaminants or 

irritation occurs,

or breathing becomes diffi cult

or dizziness or other distress occurs

Equipment malfunction

Incorrect assembly

Misuse

Pressure not within manufacturer’s 

guidelines

Leave the work area immediately 

and notify your supervisor. Do not 

use the dual airline system until the 

performance check in the 

Assembly 

Section

 of this 

User Instruction

 is 

completed and the equipment is 

checked by your supervisor.

If using the combination dual airline 

breathing tubes in air purifying mode, 

replace the cartridges or fi lters

Decrease or loss of airfl ow

Supplied air hose is kinked, split or 

restricted

Breathing tube disconnected at the 

facepiece or at air control valve

Supplied air hose disconnected at air 

control valve or fi lter and regulator panel

Decrease in pressure at fi lter and 

regulator panel

Remove kink or equipment that may 

have rolled onto the hose. Replace 

hose if cut or split.

Ensure breathing tube is connected 

Inspect and reconnect hose fi ttings

Check pressure and readjust to 

required pressure based upon hose 

length and 3M™ Air Control Valve 

SA-1009 or SA-1029 used

Replace old, dirty fi lter(s) in fi lter 

and regulating panel that could be 

restricting airfl ow

Breathing tube cracks or ruptures

Contact with organic solvents

Clean only with warm water and mild 

detergent

IMPORTANT NOTICE

WARRANTY:

 In the event any 3M PSD product is found to be defective in material, workmanship, or not in conformation 

with any express warranty for a specifi c purpose, 3M’s only obligation and your exclusive remedy shall be, at 3M’s option, to 

repair, replace or refund the purchase price of such parts or products upon timely notifi cation thereof and substantiation that 

the product has been stored, maintained and used in accordance with 3M’s written instructions.

EXCLUSIONS TO WARRANTY: THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY IMPLIED WARRANTY OF 

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OTHER WARRANTY OF QUALITY, EXCEPT OF TITLE AND 

AGAINST PATENT INFRINGEMENT.

Limitation of Liability:

 Except as provided above, 3M shall not be liable or responsible for any loss or damage, whether 

direct, indirect, incidental, special or consequential, arising out of sale, use or misuse of 3M PSD products, or the user’s 

inability to use such products. THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE.

FOR MORE INFORMATION

In United States, contact:

Website: www.3M.com/PPESafety 

Technical Assistance: 1-800-243-4630

For other 3M products:

1-800-3M-HELPS or 1-651-737-6501

RENSEIGNEMENTS SUPPLÉMENTAIRES

Aux États-Unis :

Internet : www.3M.com/PPESafety

Assistance technique : 1 800 243-4630 

Autres produits 3M :

1 800 364-3577 ou 1 651 737-6501 

PARA MAYORES INFORMES

En Estados Unidos:

Sitio Web: www.3M.com/PPESafety 

Soporte técnico: 1-800-243-4630

Para otros productos 3M:

1-800-3M-HELPS o 1-651-737-6501

PARA MAIS INFORMAÇÕES 

Nos Estados Unidos, entre em contato com: 

Website: www.3M.com/PPESafety 

Assistência Técnica: 1-800-243-4630 

Para outros produtos 3M: 

1-800-3M-HELPS ou 1-651-737-6501

Summary of Contents for SA-1500



























Reviews: