3DHISTECH Ltd. Pannoramic SCAN II 2.0 User Manual Download Page 8

Page: 8 / 142

Pannoramic SCAN II 2.0 User’s Guide

Character Formats and Symbols

Declaration of Conformity

3DHISTECH Ltd. declares that the product Pannoramic SCAN II slide scanner is designed and produced

with consideration of specified requirements according to the standards listed below:

IEC 61010-1:2010, “Safety Requirements for Electrical Equipment for Measurement, Control, and

Laboratory Use - Part 1: General Requirements”

IEC 61010-2-101:2015, “ Safety Requirements for Electrical Equipment for Measurement, Control, and

Laboratory Use

IEC 61010-2-081:2015, “Safety requirements for electrical equipment for measurement, control and

laboratory use - Part 2-081: Particular requirements for automatic and semi-automatic laboratory
equipment for analysis and other purposes”

IEC 62471:2006, “Photobiological safety of lamps and lamp systems”

IEC 61326-2-6:2012, “Electrical equipment for measurement, control and laboratory use - EMC

requirements - Part 2-6: Particular requirements - In vitro diagnostic (IVD) medical equipment”

There is no further operator (user) action required in case of residual risks.

Further information may be obtained from the distributor:

Richard Allan Scientific Co.
Subsidiary of Thermo Fisher Scientific
4481 Campus Drive
Kalamazoo MI 49008, USA
US Toll Free 1(800) 522-7270

Tudor Road, Manor Park
Runcorn, WA7 1TA
United Kingdom
+44 (0) 800 018 9396
+44 (0) 1928 534 000

June 4, 2018 - Rev. 2

3DHISTECH Ltd.

8(142)

For research and education uses only, not for use in diagnostic procedures.

Summary of Contents for Pannoramic SCAN II 2.0















































































































































Search results

Summary of Contents for Pannoramic SCAN II 2.0

Reviews:

3DHISTECH Ltd. Pannoramic SCAN II 2.0, User Manual, Page: 8 / 142

Search results

Summary of Contents for Pannoramic SCAN II 2.0

Reviews: