3DHISTECH Ltd. Pannoramic SCAN II 2.0 User Manual Download Page 110

Page: 110 / 142

Pannoramic SCAN II 2.0 User’s Guide

5 Scanning modes and settings

▪

Grab new comp

Click this button to create a new compensation image for barcode.

NOTE:

New compensation image for barcode can be recorded only if MIL is used for

barcode identification.

•

Barcode types

◦

Linear

◦

Stacked linear

◦

Postal

◦

Two-dimensional

◦

Second barcode priority

The software is capable to read two barcodes at the same time. If activated, the second

barcode will be the barcode used for slide identification.

Note:

When having two barcodes on the slide, barcode layout must be

consequential.

June 4, 2018 - Rev. 2

3DHISTECH Ltd.

110(142)

For research and education uses only, not for use in diagnostic procedures.

Summary of Contents for Pannoramic SCAN II 2.0















































































































































Search results

Summary of Contents for Pannoramic SCAN II 2.0

Reviews:

3DHISTECH Ltd. Pannoramic SCAN II 2.0, User Manual, Page: 110 / 142

Search results

Summary of Contents for Pannoramic SCAN II 2.0

Reviews: