388
C
HAPTER
38: R
OUTE
C
APACITY
C
ONFIGURATION
n
The safety-value must be greater than the limit-value.
Enabling/Disabling
Automatic Protocol
Connection Recovery
c
CAUTION:
If automatic protocol recovery is disabled, the broken OSPF or BGP
connection will not recover even when the free memory exceeds the safety value.
Therefore, do not disable this function if not necessary.
Displaying Route
Capacity
Configuration
After the above configuration, you can use the
display
command in any view to
display and verify the route capacity configuration.
Table 315
Set the lower limit and the safety value of switch memory
Operation Command
Description
Enter system view
system-view
-
Set the lower limit and the
safety value of switch
memory
memory
{
safety
safety-value
|
limit
limit-value
}*
Optional
safety-value
defaults to 40
and
limit-value
defaults to
30.
Table 316
Enable automatic protocol recovery
Operation Command Description
Enter system view
system-view
-
Enable automatic
protocol recovery
memory auto-establish
enable
Optional
By default, automatic protocol
connection recovery is enabled.
Disable automatic
protocol connection
recovery
memory auto-establish
disable
Optional
Perform this configuration with caution.
Table 317
Display route capacity configuration
Operation Command
Description
Display memory occupancy of a
switch
display memory
[
unit
unit-id
]
Optional
Display the route capacity
related memory setting and
state information
display memory limit
Optional
Summary of Contents for Switch 7754
