3Com Switch 7754 Configuration Manual Download Page 121 | Manualshive

Page: 121 / 940

background image

14

S

UPER

VLAN

n

Only the 96Gbps switch fabrics support the super VLAN.

Super VLAN Overview

To save IP address resources, the super VLAN concept (also known as VLAN
aggregation) was developed. Its principle is like this: a super VLAN may include
multiple sub VLANs, with each as a broadcast domain. Layer 2 isolation is
implemented between sub VLANs. The super VLAN can be configured with a Layer
3 interface, but not the sub VLAN.

When users in different sub VLANs want Layer 3 communication, they use the IP
address of the Layer 3 interface of the super VLAN as their gateway address. IP
address resources are saved since multiple sub VLANs share one IP address.

At the same time, in order to realize the Layer 3 connectivity between the sub
VLANs and between the sub VLAN and other networks, ARP proxy function is
used. ARP proxy enables Layer 3 connectivity between Layer 2 isolated ports by
performing ARP request and forwarding and handling response packets.

Super VLAN
Configuration

Super VLAN

Configuration Tasks

Configuring a Super

VLAN

You can configure multiple super VLANs for a switch. You can use the following
commands to specify a VLAN as a super VLAN. After a VLAN is configured as a
super VLAN, the configuration of corresponding VLAN interfaces and IP addresses
is the same as the configuration for an ordinary VLAN.

Table 68

Super VLAN configuration tasks

Operation Description Related

section

Configure a super VLAN

Optional

“Configuring a Super VLAN”
on page 121

Configure a sub VLAN

Optional

“Configuring a Sub VLAN” on
page 122

Configure the mapping
between super VLAN and sub
VLAN

Optional

“Configuring the Mapping
between a Super VLAN and a
Sub VLAN” on page 122

Configure super VLAN to
support DHCP relay

Optional

“Configuring Super VLAN to
Support DHCP Relay” on page
123

«
...
119
120
121
122
123
...
»

Summary of Contents for Switch 7754













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Switch 7754

i-bus KNX IPR/S 3.5.1

Brand: ABB Pages: 44

Brand: Sagem Pages: 19

Brand: Paradyne Pages: 16

Brand: E-Lins Pages: 59

Brand: E-Lins Pages: 11

Brand: E-Lins Pages: 9

Brand: E-Lins Pages: 5

Network Video Recorders

Brand: e-Line Technology Pages: 34

Brocade X6-8 Director

Brand: Broadcom Pages: 207

Brand: Juniper Pages: 190

APS6-400 Series

Brand: Eaton Pages: 114

Brand: IDT Pages: 93

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

ControlPoint 2000

Brand: 4Home Pages: 20

ELITENAS EN104L+(B)

Brand: Sans Digital Pages: 9

HHM Series HHM2409

Brand: TDK Pages: 2

Brand: Acromag Pages: 23

Brand: Top Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands