manualshive.com logo in svg

3Com Switch 7754, Configuration Manual

The 3Com Switch 7754 is a high-performance networking solution that provides exceptional connectivity for small to medium-sized businesses. With a comprehensive datasheet and user manual available for download, users can easily configure and optimize their network settings. Visit manualshive.com to freely download the essential documentation for maximizing the potential of this product.

Share
Download
background image

326

C

HAPTER

 34: OSPF C

ONFIGURATION

■

If the network type is broadcast or NBMA, ensure that there is at least one 
interface with a priority greater than zero.

■

If an area is set to a stub area, ensure that the area is set to a stub area for all 
the routers connected to this area.

■

Ensure that the interface types of two neighboring routers are consistent.

■

If two or more areas are configured, ensure that at least one area is configured 
as the backbone area; that is, the area ID of an area is 0.

■

Ensure that the backbone area is connected to all the other areas.

■

Ensure that no virtual link passes through a stub area.

Global fault removal: If OSPF still cannot discover the remote routes after the 
above procedure is performed, check the following configurations:

■

If two or more areas are configured on a router, at least one area should be 
configured to be connected to the backbone area.

As shown in Figure 75, Router A and Router D are configured to belong to only 
one area, whereas Router B (Area 0 and Area 1) and Router C (Area 1 and Area 2) 
are configured to belong to two areas. Router B also belongs to area 0, which 
meets the requirement. However, none of the areas of Router C is Area 0. 
Therefore, a virtual link should be set up between Router C and Router B. Ensure 
that Area 2 and Area 0 (backbone area) are interconnected.

Figure 75   

OSPF area

 

■

A virtual link cannot pass through a stub area. The backbone area (Area 0) 
cannot be configured as a stub area. So, if a virtual link has been set up 
between RTB and RTC, neither Area 1 nor Area 0 can be configured as a stub 
area. In Figure 75, only Area 2 can be configured as a stub area.

■

A router in a stub area cannot receive external routes.

■

The backbone area must guarantee the connectivity between various nodes.

Area 0

Area 1

Area 2

ABR

ABR

Transit Area

Virtual Link

Router A

Router B

Router C

Router D

Summary of Contents for Switch 7754













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Switch 7754

D-Link DES-3526 - Switch - Stackable Manual preview
DES-3526 - Switch - Stackable
Brand: D-Link Pages: 258
4IPNET WHG301 User Manual preview
WHG301
Brand: 4IPNET Pages: 97
ZALMAN RESERATOR 1 Manual preview
RESERATOR 1
Brand: ZALMAN Pages: 22
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
B&B Electronics Parallel Printer Card PIOC User Manual preview
Parallel Printer Card PIOC
Brand: B&B Electronics Pages: 16
Toto Link IP04229 User Manual preview
IP04229
Brand: Toto Link Pages: 55
Hama 00039747 Operating Instruction preview
00039747
Brand: Hama Pages: 6
MC PCIe-DIO96H User Manual preview
PCIe-DIO96H
Brand: MC Pages: 21
Jaycar Electronics Duinotech Lilypad Plus XC3920 Quick Start preview
Duinotech Lilypad Plus XC3920
Brand: Jaycar Electronics Pages: 2
ANTAIRA LMP-1202G-SFP Series Hardware Manual preview
LMP-1202G-SFP Series
Brand: ANTAIRA Pages: 19
Alarm NX-208E Installation Manual preview
NX-208E
Brand: Alarm Pages: 5
Genexis FiberTwist G6426 Installation Manual preview
FiberTwist G6426
Brand: Genexis Pages: 9
Primera Disc Publisher XR Installation Instructions preview
Disc Publisher XR
Brand: Primera Pages: 2
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Brand: Adaptec Pages: 14
MiWire SeaWire Pro User Manual preview
SeaWire Pro
Brand: MiWire Pages: 24
Juniper MX480 Hardware Manual preview
MX480
Brand: Juniper Pages: 420

Brands by name

Popular brands

Load more brands