manualshive.com logo in svg

3Com Switch 7754, Configuration Manual

The 3Com Switch 7754 is a high-performance networking solution that provides exceptional connectivity for small to medium-sized businesses. With a comprehensive datasheet and user manual available for download, users can easily configure and optimize their network settings. Visit manualshive.com to freely download the essential documentation for maximizing the potential of this product.

Share
Download
background image

Troubleshooting IPX

147

# Assign the network number 3 to VLAN interface 2 to enable IPX on the VLAN 
interface.

[Switch] interface Vlan-interface 2

[Switch-Vlan-interface2] ipx network 3 

# Set the packet encapsulation format to Ethernet_SNAP on VLAN interface 2.

[Switch-Vlan-interface2] ipx encapsulation snap

[Switch-Vlan-interface2] quit 

# Assign the network number 1000 to VLAN interface 1 to enable IPX on the 
VLAN interface.

[Switch] interface Vlan-interface 1

[Switch-Vlan-interface1] ipx network 1000 

# Configure a static route with the destination network number 2.

[Switch-Vlan-interface1] quit

[Switch] ipx route-static 2 1000.000f-e20f-0000 tick 7 hop 2 

# Configure a service information entry, indicating that Server can provide the file 
service.

[Switch] ipx service 4 fileserver 2.0000-0c91-f61f 451 hop 2 

# Configure a service information entry, indicating that the server can provide the 
printing service.

[Switch] ipx service 7 printserver 2.0000-0c91-f61f 5 hop 2 

Troubleshooting IPX

Troubleshooting IPX forwarding

Symptom 1: A destination address cannot be pinged.

Solutions:

■

Check whether the destination address is correct.

■

Use the display ipx interface command to check whether the network number 
and IPX frame encapsulation format configured on the interface of the switch 
are consistent with those configured on the connected interface.

■

Use the display ipx routing-table command to check whether the destination 
network is reachable.

■

Use the debugging ipx packet command to enable debugging for IPX packets. 
Check whether IPX packets are correctly received, transmitted, forwarded, and 
dropped.

Symptom 2: Packets are dropped.

Solutions:

■

If the IPX packet debugging information shows that a packet is dropped 
because “Packet size is greater than interface MTU!”, perform the following 

Summary of Contents for Switch 7754













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Switch 7754

D-Link DSL-504T Manual preview
DSL-504T
Brand: D-Link Pages: 99
D-Link DI-804V Datasheet preview
DI-804V
Brand: D-Link Pages: 5
D-Link DES-1210-08P Manual preview
DES-1210-08P
Brand: D-Link Pages: 15
D-Link AirPro DWL-6000AP Manual preview
AirPro DWL-6000AP
Brand: D-Link Pages: 65
Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Brand: Lattice Semiconductor Pages: 15
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Brand: Tandberg Data Pages: 28
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
TRENDnet TE100-S16 - 10/100Mbps Ethernet Switch User Manual preview
TE100-S16 - 10/100Mbps Ethernet Switch
Brand: TRENDnet Pages: 15
Daedalon EC-33 Instruction Manual preview
EC-33
Brand: Daedalon Pages: 6
Cabletron Systems MMAC-Plus 9G536-04 User Manual preview
MMAC-Plus 9G536-04
Brand: Cabletron Systems Pages: 42
ADTRAN Express L128FP User Manual preview
Express L128FP
Brand: ADTRAN Pages: 161
Matrix Switch Corporation MSC-2HD1624S Product Manual preview
MSC-2HD1624S
Brand: Matrix Switch Corporation Pages: 54
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Brand: IEI Technology Pages: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Brand: RadioSPECTRAL Pages: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Brand: ZALMAN Pages: 9
Gtran Wireless DotSurfer GPC-2100 User Manual preview
DotSurfer GPC-2100
Brand: Gtran Wireless Pages: 44
Vista VIPER H4 User Manual preview
VIPER H4
Brand: Vista Pages: 93
Tenda FH456 User Manual preview
FH456
Brand: Tenda Pages: 82

Brands by name

Popular brands

Load more brands