manualshive.com logo in svg

3Com Switch 7754, Configuration Manual

The 3Com Switch 7754 is a high-performance networking solution that provides exceptional connectivity for small to medium-sized businesses. With a comprehensive datasheet and user manual available for download, users can easily configure and optimize their network settings. Visit manualshive.com to freely download the essential documentation for maximizing the potential of this product.

Share
Download
background image

23

L

INK

 A

GGREGATION

 C

ONFIGURATION

Overview

Introduction to Link

Aggregation

Link aggregation aggregates multiple physical Ethernet ports into one logical link, 
also called an aggregation group. It allows you to increase bandwidth by 
distributing incoming/outgoing traffic on the member ports in the aggregation 
group. In addition, it provides reliable connectivity because these member ports 
can dynamically back up each other.

Depending on different aggregation modes, aggregation groups fall into three 
types: manual, static LACP, and dynamic LACP. Depending on whether or not load 
sharing is implemented, aggregation groups can be load-sharing or 
non-load-sharing aggregation groups.

For the member ports in an aggregation group, their basic configuration must be 
the same. The basic configuration includes STP, QoS, VLAN, port attributes and 
other associated settings.

■

STP configuration, including STP status (enabled or disabled), link attribute 
(point-to-point or not), STP priority, maximum transmission speed, loop 
prevention status, root protection status, edge port or not.

■

QoS configuration, including traffic limiting, priority marking, default 802.1p 
priority, bandwidth assurance, congestion avoidance, traffic redirection, traffic 
statistics, and so on.

■

VLAN configuration, including permitted VLANs, and default VLAN ID.

■

Port attribute configuration, including port rate, duplex mode, and link type 
(Trunk, Hybrid or Access). The ports for a manual or static aggregation group 
must have the same link type, and the ports for a dynamic aggregation group 
must have the same rate, duplex mode and link type.

Introduction to LACP

The purpose of the link aggregation control protocol (LACP) is to implement 
dynamic link aggregation and deaggregation. This protocol is defined in 
IEEE802.3ad. It uses link aggregation control protocol data units (LACPDUs) for 
information exchange between LACP-enabled devices.

After LACP is enabled on a port, the port sends LACPDUs to notify the remote 
system of its system LACP priority, system MAC address, port LACP priority, port 
number, and operational key. Upon receipt of an LACPDU, the remote system 
compares the received information with the information received on other ports to 
determine the ports that can operate as selected ports. This allows the two 
systems to reach an agreement on the states of the related ports.

Summary of Contents for Switch 7754













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Switch 7754

H3C S3100 Series Operation Manual preview
S3100 Series
Brand: H3C Pages: 1057
NEC N8104-128 Installation Manual preview
N8104-128
Brand: NEC Pages: 47
3Com IntelliJack NJ200 Datasheet preview
IntelliJack NJ200
Brand: 3Com Pages: 4
N-Tron 7018 User Manual & Installation Manual preview
7018
Brand: N-Tron Pages: 138
STONEFLY DR365V-2404 Setup Manual preview
DR365V-2404
Brand: STONEFLY Pages: 48
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Brand: ekwb Pages: 2
Macsense MPC-200 User Manual preview
MPC-200
Brand: Macsense Pages: 13
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
Aewin Technologies SCB-9651 User Manual preview
SCB-9651
Brand: Aewin Technologies Pages: 86
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
MICRADIGITAL F5D7630uk4A-E Speci?Cations preview
F5D7630uk4A-E
Brand: MICRADIGITAL Pages: 2
Pilz PNOZ mc3p Operating Instructions Manual preview
PNOZ mc3p
Brand: Pilz Pages: 12
IBA FOB-SDexp Manual preview
FOB-SDexp
Brand: IBA Pages: 36
Data Translation DT9835 Getting Started Manual preview
DT9835
Brand: Data Translation Pages: 62
DIGITAL-LOGIC MICROSPACE MSEBX800 User Manual preview
MICROSPACE MSEBX800
Brand: DIGITAL-LOGIC Pages: 53
DAPAudio D2081 Manual preview
D2081
Brand: DAPAudio Pages: 33

Brands by name

Popular brands

Load more brands