3Com Switch 7754 Configuration Manual Download Page 129 | Manualshive

Page: 129 / 940

background image

Configuring an IP Address for a VLAN Interface

129

address, and the part corresponding to the remaining “0” bits in the mask is the
host address. If there is no subnet division, the subnet mask uses the default value
and the length of 1s in the mask is equal to the net-id length. Therefore, for IP
addresses of classes A, B and C, the default values of the corresponding subnet
masks are 255.0.0.0, 255.255.0.0 and 255.255.255.0 respectively.

The mask can be used to divide a Class A network containing more than
16,000,000 hosts or a Class B network containing more than 60,000 hosts into
multiple small networks. Each small network is called a subnet. For example, for
the Class B network address 138.38.0.0, the mask 255.255.224.0 can be used to
divide the network into eight subnets: 138.38.0.0, 138.38.32.0, 138.38.64.0,
138.38.96.0, 138.38.128.0, 138.38.160.0, 138.38.192.0 and 138.38.224.0 (see
Figure 38). Each subnet can contain more than 8000 hosts.

Figure 38

Subnet division of the IP address

Configuring an IP
Address for a VLAN
Interface

A VLAN interface obtains an IP address with an IP address configuration
command. Generally, it is enough to configure one IP address for a VLAN
interface. However, you can configure up to eight IP addresses for a VLAN
interface so that the interface can be connected to several subnets. Among these
IP addresses, one is the primary IP address and the others are secondary ones.

10001010, 00100110, 000 00000, 00000000

ClassB

138.38.0.0

Subnet mask

255.255.224.0

11111111, 11111111, 111 00000, 00000000

11111111, 11111111, 000 00000, 00000000

Standard
mask

255.255.0.0

Subnet address:

000

Subnet address: 138.38. 0. 0

001

Subnet address: 138.38. 32. 0

010

Subnet address: 138.38. 64. 0

011

Subnet address: 138.38. 96. 0

100

Subnet address: 138.38.128. 0

101

Subnet address: 138.38.160. 0

110

Subnet address: 138.38.192. 0

111

Subnet address: 138.38.224. 0

Subnet
number

Host
number

Subnet address:

10001010, 00100110, 000 00000, 00000000

ClassB

138.38.0.0

Subnet mask

255.255.224.0

11111111, 11111111, 111 00000, 00000000

11111111, 11111111, 000 00000, 00000000

Standard
mask

255.255.0.0

Subnet address:

000

Subnet address: 138.38. 0. 0

001

Subnet address: 138.38. 32. 0

010

Subnet address: 138.38. 64. 0

011

Subnet address: 138.38. 96. 0

100

Subnet address: 138.38.128. 0

101

Subnet address: 138.38.160. 0

110

Subnet address: 138.38.192. 0

111

Subnet address: 138.38.224. 0

Subnet
number

Host
number

Subnet address:

10001010, 00100110, 000 00000, 00000000

ClassB

138.38.0.0

Subnet mask

255.255.224.0

11111111, 11111111, 111 00000, 00000000

11111111, 11111111, 000 00000, 00000000

Standard
mask

255.255.0.0

Subnet address:

000

Subnet address: 138.38. 0. 0

001

Subnet address: 138.38. 32. 0

010

Subnet address: 138.38. 64. 0

011

Subnet address: 138.38. 96. 0

100

Subnet address: 138.38.128. 0

101

Subnet address: 138.38.160. 0

110

Subnet address: 138.38.192. 0

111

Subnet address: 138.38.224. 0

Subnet
number

Host
number

Subnet address:

10001010, 00100110, 000 00000, 00000000

ClassB

138.38.0.0

Subnet mask

255.255.224.0

11111111, 11111111, 111 00000, 00000000

11111111, 11111111, 000 00000, 00000000

Standard
mask

255.255.0.0

Subnet address:

000

Subnet address: 138.38. 0. 0

001

Subnet address: 138.38. 32. 0

010

Subnet address: 138.38. 64. 0

011

Subnet address: 138.38. 96. 0

100

Subnet address: 138.38.128. 0

101

Subnet address: 138.38.160. 0

110

Subnet address: 138.38.192. 0

111

Subnet address: 138.38.224. 0

Subnet
number

Host
number

Subnet address:

Table 74

Configure an IP address for a VLAN interface

Operation Command

Description

Enter system view

system-view

-

Enter VLAN interface view

interface Vlan-interface

vlan-id

-

Configure an IP address
for a VLAN interface

ip address

ip-address

{

mask |

mask-length

} [

sub

]

Required

By default, a VLAN
interface has no IP address.

«
...
127
128
129
130
131
...
»

Summary of Contents for Switch 7754













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Switch 7754

Brand: N-Tron Pages: 101

Univerge SV9300

Brand: NEC Pages: 26

Brand: NEC Pages: 20

DS2000 IntraMail

Brand: NEC Pages: 2

Brand: Patton electronics Pages: 8

Brand: ICP DAS USA Pages: 48

Brand: ICP DAS USA Pages: 24

Brand: ICP DAS USA Pages: 4

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

Brand: SUNRICH TECHNOLOGY Pages: 5

Brand: SIIG Pages: 20

Brand: Seattle Computer Products Pages: 31

Brand: Cameo Pages: 23

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brand: Longshine Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands