manualshive.com logo in svg

3Com 4210G Series, Configuration Manual, Page: 67 / 1133

Share
Download
3Com 4210G Series Configuration Manual Download Page 67

 

3-2 

Displaying and Maintaining Isolation Groups 

To do… 

Use the command… 

Remarks 

Display the isolation group 
information  

display port-isolate group

 

Available in any view 

 

Port Isolation Configuration Example 

Network requirements 

z

 

Users Host A, Host B, and Host C are connected to GigabitEthernet 1/0/1, GigabitEthernet 1/0/2, 
and GigabitEthernet 1/0/3 of Device. 

z

 

Device is connected to the Internet through GigabitEthernet 1/0/4. 

z

 

GigabitEthernet 1/0/1, GigabitEthernet 1/0/2, GigabitEthernet1/0/3 and GigabitEthernet1/0/4 
belong to the same VLAN. It is desired that Host A, Host B, and Host C cannot communicate with 
one another at Layer 2, but can access the Internet.   

Figure 3-1 

Networking diagram for port isolation configuration 

 

 

Configuration procedure 

# Add ports GigabitEthernet 1/0/1, GigabitEthernet 1/0/2 and GigabitEthernet 1/0/3 to the isolation 
group.  

<Device> system-view 

[Device] interface GigabitEthernet 1/0/1 

[Device-GigabitEthernet1/0/1] port-isolate enable 

[Device-GigabitEthernet1/0/1] quit 

[Device] interface GigabitEthernet 1/0/2 

[Device-GigabitEthernet1/0/2] port-isolate enable 

[Device-GigabitEthernet1/0/2] quit 

[Device] interface GigabitEthernet 1/0/3 

[Device-GigabitEthernet1/0/3] port-isolate enable 

# Display the information about the isolation group.   

<Device> display port-isolate group 

 Port-isolate group information: 

Summary of Contents for 4210G Series














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments