manualshive.com logo in svg

3Com 4210G Series, Configuration Manual, Page: 127 / 1133

Share
Download
3Com 4210G Series Configuration Manual Download Page 127

 

5-17 

2)  Configure CDP-compatible LLDP on Switch A.   
# Enable LLDP globally and enable LLDP to be compatible with CDP globally.   

[SwitchA] lldp enable

   

[SwitchA] lldp compliance cdp 

# Enable LLDP (you can skip this step because LLDP is enabled on ports by default), configure LLDP 
to operate in TxRx mode, and configure CDP-compatible LLDP to operate in TxRx mode on 
GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2.   

[SwitchA] interface gigabitethernet 1/0/1 

[SwitchA-GigabitEthernet1/0/1] lldp enable 

[SwitchA-GigabitEthernet1/0/1] lldp admin-status txrx 

[SwitchA-GigabitEthernet1/0/1] lldp compliance admin-status cdp txrx 

[SwitchA-GigabitEthernet1/0/1] quit 

[SwitchA] interface gigabitethernet 1/0/2 

[SwitchA-GigabitEthernet1/0/2] lldp enable 

[SwitchA-GigabitEthernet1/0/2] lldp admin-status txrx 

[SwitchA-GigabitEthernet1/0/2] lldp compliance admin-status cdp txrx 

[SwitchA-GigabitEthernet1/0/2] quit 

3)  Verify the configuration 

# Display the neighbor information on Switch A.   

[SwitchA] display lldp neighbor-information 

CDP neighbor-information of port 1[GigabitEthernet1/0/1]: 

  CDP neighbor index : 1 

  Chassis  ID         :  SEP00141CBCDBFE  

  Port  ID            :  Port  1 

  Sofrware  version   :  P0030301MFG2 

  Platform           :  Cisco  IP  Phone  7960 

  Duplex             :  Full 

 

CDP neighbor-information of port 2[GigabitEthernet1/0/2]: 

  CDP neighbor index : 2 

  Chassis  ID         :  SEP00141CBCDBFF 

  Port  ID            :  Port  1 

  Sofrware  version   :  P0030301MFG2 

  Platform           :  Cisco  IP  Phone  7960 

  Duplex             :  Full 

As the sample output shows, Switch A has discovered the IP phones connected to GigabitEthernet 
1/0/1 and GigabitEthernet 1/0/2, and has obtained their LLDP device information. 

Summary of Contents for 4210G Series














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments