Zycoo UC510 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 84

Zycoo UC510 Скачать руководство пользователя страница 83

Copyright © ZYCOO All Rights Reserved

82

/

84

Click

【

Administration

】



【

Backup&Restore

】

:

Click the “Take a Backup” button to back up the settings, and you will find the backup file’s name

and date. You can click

to download the backup file and save it to your computer; when you

need to recovery the settings, you can upload it from "Upload Backup File", or click the “Restore”
button of the relative backup file to recovery the settings

Notice:

All functions will not be available during backup & restore; please prepare before operation.
Please do not change the backup files in case of any failure of backup or restore.

5.1.7 Troubleshooting

Troubleshooting is used for network connection test.

Click

【

Administration

】



【

Troubleshooting

】



【

Ping

】

to test:

Input the destination address and contract number, then click "Run" to wait for the results.

Test route:

Click

【

Administration

】



【

Troubleshooting

】



【

Traceroute

】

to test:

«
...
81
82
83
84
»

Содержание UC510





















































































Отзывы:

Нет отзывов