Zycoo UC510 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 84

Zycoo UC510 Скачать руководство пользователя страница 17

Copyright © ZYCOO All Rights Reserved

16

/

84

Delete[ ]digits prefix

Define how many digits will be deleted from the dialed number.
For example, user dialed 94166445775 and you selected to delete 1
digit, then 4166445775 is sent out to the trunk.

Auto-add digit[ ]

If add digit “9”, when dial 12345, 912345 will be sent.

3.2

Inbound Control

3.2.1 Inbound Routes

Click

【

Inbound Control

】



【

Inbound Routes

】

General

Distinctive Ring Tone

：

mapping the custom ring tone file, e.g.: Set distinctive ring tone as

“External”, the phone will play this ring tone when receiving the call.

Note:

The phone must support such feature as well.

Select all calls coming in on a specific port (FXO/VoIP) and select which destination (Extension
User, IVR, Queue, Conference Bridge, IVR, etc) should answer those calls. Setting the label will
assign this label to be displayed.

Port DIDs

To have incoming calls from a PSTN trunk port (FXO trunk) answered by a specific extension user,
call queue, conference bridge, or IVR, please configure here:

Click

【

Port DIDs

】



【

New Port DIDs

】

:

«
...
15
16
17
18
19
...
»

Содержание UC510





















































































Отзывы:

Нет отзывов