Zycoo UC510 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 84

Zycoo UC510 Скачать руководство пользователя страница 54

Copyright © ZYCOO All Rights Reserved

53

/

84

LAN3 VLAN MAC Address

Set the IP address of VLAN for LAN3. You need to distribute a
new and independent MAC address which cannot be same as
the current system.

Notice

VLAN IP address of LAN3/LAN2/LAN1 must be in different network segments;
MAC address must be different from LAN port; MAC address must be different during Port VLAN.

DHCP Server Setup

DHCP Server can used to automatically assign IP address to terminals accessing UC510/520.
Only the IP address range set here can be assigned automatically.

Reference:

Item

Explanation

DHCP Type

Enable or Disable DHCP

Start IP Address

Set Start IP address, which must be same as the LAN or Extended LAN

End IP Address

Set End IP address, which must be same as the LAN or Extended LAN

Subnet Mask

Set subnet mask address

Primary DNS Server

Set primary DNS sever address

Secondary DNS
Server

Set secondary DNS sever address

TFTP Server

Set TFTP server address, which supports OPTION66, and be used for IP
PBX Auto Provision

Default Gateway

Set default gateway address; it is recommended to be the LAN or
extended LAN IP address, otherwise, LAN user cannot surf internet.

Lease Time

Set the lease time of IP

Statically Assigned

Set statically assigned MAC and IP(at most 3). The client will receive the
corresponding IP address when DHCP is enabled.

«
...
52
53
54
55
56
...
»

Содержание UC510





















































































Отзывы:

Нет отзывов