Zycoo UC510 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 84

Zycoo UC510 Скачать руководство пользователя страница 62

Copyright © ZYCOO All Rights Reserved

61

/

84

Network Mode

Alternative Wireless protocol, includes 11b/g/n mixed
mode, 11b only, 11g only and 11n only(2.4G)

Network Name(SSID)

SSID(Service  Set  Identification)  also  known  as  Wi-Fi  name,
allows your wireless network to be easily distinguished from
other  wireless  networks.  In  addition,  Hidden  option  can
make  SSID  invisible,  nobody  can  search  this  Wi-Fi;  Isolated
option is used for partitioning VLAN under the same SSID; in
other  words,  Isolated  option  users  could  not  visit  others
Host in the same SSID

BSSID

BSSID is Basic Service Set Identifier, which is defined as MAC
address of Wi-Fi router in IEEE 802.11.

Frequency (Channel)

Wi-Fi Frequency(Channel). It can be “AutoSelect” or selected
as a specific frequency. The default is “AutoSelect”

Operating Mode

Operation mode contains Mixed and Green Field.
Mixed Mode

：

wireless network card can identify Pre-N AP,

but throughput would be affected

；

Green Field Mode

：

It will reach high throughput, but

compatibility and system security will be affected
The default is Mixed Mode

Channel Bandwidth

Supports  20MHz  and  20MHZ/40MHz  channel.  In  IEEE
802.11N  mode,  two  20MHZ  channels  can  be  bundled  to  a
40MHz  channel;  it  can  be  used  as  two  channels  in  real
working  environment  (one  is  primary,  the  other  one  is
secondary);  this  will  double  the  transmission  rate  or
promote more.
The default is 20/40

Guard Interval

Is used to ensure that distinct transmissions do not interfere
with  one  another.  These  transmissions  may  belong  to
different  users  (as  in  TDMA)  or  to  the  same  user  (as  in
OFDM).
Send  interval  between  the  wireless  signal;  long  interval  or
auto interval is alternative

MCS

MCS(Modulation and Coding Scheme) is the wireless rate of
802.11n. Please select the index value of MCS; each value
corresponds to a communication rate determined by a set of
parameters.
The default is Auto.

Reverse Direction Grant(RDG)

Is used to guarantee the normal communication between
terminal and AP, especially in radio interference.

Extension Channel

If  Frequency(Channel)  is  “AutoSelect”,  then  no  extension
channels;  If  specific  channel  is  selected,  there  will  be
corresponding  extension  channel.  And  when  Channel
Bandwidth  is  20MHz,  there  will  not  be  extension  channel;

«
...
60
61
62
63
64
...
»

Содержание UC510





















































































Отзывы:

Нет отзывов