Zycoo UC510 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 84

Zycoo UC510 Скачать руководство пользователя страница 69

Copyright © ZYCOO All Rights Reserved

68

/

84

Statistical parameter table

：

Item

Description

Tx Success

Successful transmission package size (by byte)

Tx Retry Count

Transmission retry count (by byte); PER (Percent Ratio)
count by percentage.

Tx Fail after retry

Statistics of Retry after transmission failure(by byte); PLR :
Packet Loss Rate

RTS Succeed To Receive CTS

Received CTS successfully after sending RTS
(RTS/CTS refer to Request to Send and Clear to Send, flow
control signal)

RTS Fail To Receive CTS

Failed to receive CTS after sending RTS
(RTS/CTS refer to Request to Send and Clear to Send, flow
control signal)

Frames Received Successfully

Receive frames successfully (by byte)

Frames Received With CRC Error

Received the frame CRC errors, in bytes, PER as a percentage

SNR

Signal-to-Noise Ratio is defined as the power ratio between
a signal(meaningful information) and the background
noise(unwanted signal). The greater the SNR, the smaller
the noise power is.

WPS

WPS (Wi-Fi Protected Setup

)

was launched by the Wi-Fi alliance as a new Wi-Fi security setting,

mainly  in  order  to  solve  the  long  wireless  encryption  authentication  set.  The  drawbacks  of  the
steps is that it is too complex, difficult, WPS function on the wireless router can let's take a quick
easy encryption wireless network data transmission, to prevent the invasion of illegal users.

Traditionally, a Wi-Fi router limits illegal access by assigning a complicated password. This makes
it  inconvenient  to  both  memorize  and  input  the  password.  WPS  provides  a  much  easier  and
relatively more secure way of limiting illegal access and attack.

«
...
67
68
69
70
71
...
»

Содержание UC510





















































































Отзывы:

Нет отзывов