Zycoo UC510 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 84

Zycoo UC510 Скачать руководство пользователя страница 5

Copyright © ZYCOO All Rights Reserved

4

/

84

Chapter 1 Brief Introduction

1.1

Brief Introduction of UC510/UC520

UC510/520 is designed specifically as an IP Office for SOHOs (Small Office and Home Offices). The
new solution offers not only a Wi-Fi router supporting VPN Client/Server, VLAN, and external
ADSL connection... but also a fully featured IP PBX that can host up to 10 extensions with 2
analog ports connected, and supports Call Forward, Call Recording, Blind/Attendant Transfer,
and many other features.
UC510/520 is configured and managed through a single web GUI which significantly reduces the
time and effort required to install the product. This simplified management and reduction in
hardware costs through merging two products into one makes the UC510 an amazing and cost
effective solution for SOHOs.

Telephony Module: Built-in 2 FXO or 1FXOS; LTE is default in UC520.

Model

FXS

FXO

LTE

UC510

1

1

0

0

2

0

UC520

1

1

1

0

2

1

1.2

Main Features

PBX Features

BLF

Blind/Attended Transfer
Call Forward
Call Pickup
DID
DISA
Dial Plan
Follow Me
IVR/ IVR Prompts
Inbound Route
Music On Hold
Outbound Route
Phone Provisioning
Ring Group
SIP/FXO Trunk
Time Rule
Voicemail/Voicemail to Email

Router Features

Internet Access (PPPoE, Static or DHCP)
VLAN (IEEE802.1Q)
DHCP List
Blind IP to MAC
Wi-Fi Basic Setup
Wi-Fi Security Setup
Wi-Fi Mac Address Filter
Wi-Fi Advanced Setup
Online Host
NAT: Port Forwarding/DMZ Host

«
...
3
4
5
6
7
...
»

Содержание UC510





















































































Отзывы:

Нет отзывов