Zycoo UC510 Скачать руководство пользователя страница 35

Страница: 35 / 84

Reference:

Item

Explanation

SMTP Server

You  must  set  SMTP  Server  address  or  domain  connected  to  the
CooVox  IP  PBX,  which  is  used  for  sending  the  voice  message  to
Email.

Port

Port number for SMTP server. Default is 25, and it will be changed
to 465 when you enable SSL/TLS.

SSL/TSL

Enable SSL/TLS.

Enable SMTP
Authentication

If your SMTP server needs authentication, please enable this
option, and configure the following.

Username

Input username of your Email.

Password

Input password of your Email.

Click

【

Send Test

】

after configuration, the following diagram will be displayed to ask you to input

the Email for receiving.

Specify the email address and click

【

Send

】

to send the test email. Verify that email was

successfully sent or not. If no email is received, please modify the SMTP settings and try again.

3.3.4 Music Settings

Management of Music on Hold, Music on Ringback, Music on Queue.

Click

【

Advance

】



【

Music Settings

】

Содержание UC510




















































































Результаты поиска

Содержание UC510

Отзывы:

Zycoo UC510, Руководство пользователя, Страница: 35 / 84

Результаты поиска

Содержание UC510

Отзывы: