Zycoo UC510 Скачать руководство пользователя страница 14

Страница: 14 / 84

Password

Password provided by VoIP Provider.

Advanced Options

Advanced options for this trunk, e.g.: codecs, language, etc.

The outbound trunk will be in the list of VoIP Trunks when the trunk is added successfully.

FXO Trunk

Click

【

FXO Trunk

】



【

New FXO Trunk

】

FXO Trunk Reference:

Item

Explanation

Description

Description for this trunk.

Lines

Check one or two channels (FXO) to be included in this trunk group

Prefix

The prefix will be added to the dialed number automatically when this
trunk is in use.

Advanced Options

Advanced Options for this trunk, e.g.: Call Method, Busy Detection,
etc.

Select one or more of the available channels to be used for this trunk group.

Note:

each channel can only be included in one trunk group. If no channels appear then all

available channels are already defined.

3.1.3 Outbound Routes

Outbound Routes are used to define which trunk groups are used by a specific extension when
placing outbound calls. If you don't allow an extension user to place external calls, please ignore
this section.

Please configure on this page:

【

Basic

】



【

Outbound Routes

】

Содержание UC510




















































































Результаты поиска

Содержание UC510

Отзывы:

Zycoo UC510, Руководство пользователя, Страница: 14 / 84

Результаты поиска

Содержание UC510

Отзывы: