Zycoo UC510 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 84

Zycoo UC510 Скачать руководство пользователя страница 8

Copyright © ZYCOO All Rights Reserved

7

/

84

Power Supply

1 piece

1 piece

Ethernet Cable

1 piece

1 piece

Quick Installation Guide

1 piece

1 piece

Warranty Card

1 piece

1 piece

Chapter 2 Getting Started

2.1

Home

The default login URL is http://192.168.1.1:9999
After system login, the home page will display status of the system interface and system
information including model, firmware version and running time.

System Interface:

Connecting Status of Interfaces.

If an Analog module is connected, “FXO” or “FXS” will be displayed at the appropriate position. If
no Analogue module is connected then “N/A” will be displayed.
If Ethernet is connected on either LAN or WAN,“UP” will be displayed for the relevant port. If no
connection is detected on the port, “DOWN” will be displayed.
If Wi-Fi is enabled, “ON” will be displayed and if not enabled “OFF” is displayed.

System Info:

Displays device model, system version, system current time and running time.

2.2

Network Status

Network Status displays the network configuration of the system, including

WAN

,

LAN

,

VLAN

.

The network connection supports STATIC, DHCP and PPPoE. The relevant information will be

displayed after configuration from

【

Router Gateway

】



【

Internet

】

.

«
...
6
7
8
9
10
...
»

Содержание UC510





















































































Отзывы:

Нет отзывов