Zycoo UC510 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 84

Zycoo UC510 Скачать руководство пользователя страница 51

Copyright © ZYCOO All Rights Reserved

50

/

84

Manual: When L2TP is disconnected, you have to connect
manually.

PPTP

If PPTP is selected the UC510/520 will serve as a VPN client and therefore all traffic sent and
received will be encrypted, providing safe access to the business network by dialing to the
Internet Service Provider(ISP) or connecting to the internet or other network.
WAN Connection Type: Select “PPTP”

Reference:

Item

Explanation

WAN Connection Type

PPTP

Server IP

Input server IP

User Name

Set user name

Password

Set password

Address Mode

Support two modes: Static(Fixed IP)/Dynamic (DHCP Auto Config)

IP Address

Set IP address when Address Mode is Static

Subnet Mask

Set subnet mask when Address Mode is Static

Default Gateway

Set default gateway when Address Mode is Static

MPPE Encryption

Enable or Disable MPPE Encryption (Microsoft Point-to-Point
Encryption)

Operation Mode

Support two operation modes: Keep Alive/Manual.
Keep Alive: when PPTP is disconnected, system will connect again
every 60s.
Manual: when PPTP is disconnected, you have to connect manually.

LTE

LTE network connection is supported on the UC520 only by default. It supports FDD-LTE.
WAN Connection Type: Select ”LTE”

«
...
49
50
51
52
53
...
»

Содержание UC510





















































































Отзывы:

Нет отзывов