Zycoo UC510 Скачать руководство пользователя страница 72

Страница: 72 / 84

Reference:

Item

Explanation

MAC/IP/Port Filter

Enable/Disable the MAC/IP/Port filter

Default Policy

The default strategy, set up to receive or discard the
specified Mac/IP/Port of packets

Source MAC Address

Set the source host MAC address, e.g.: 00:12:0f:dd:22:01
or null

Dest. IP Address

Set the destination host IP address, such as
221.220.215.0/24 or 192.188.10.12/32 or 192.188.10.12

Source IP Address

Set the source host IP address, such as 192.168.10.0/24or
192.168.10.12/32 or 192.168.10.12

Protocol

Set the protocol type. None means all types

Dest. Port Range

Set the destination port range

Source Port Range

Set the source port range

Action

Set the action: Accept or Drop

Comment

Annotation

Basic Settings

Click

【

Apply

】

and save settings

MAC/IP/Port Filter Settings

Click

【

Apply

】

and save settings. The maximum rule count is 32.

Current MAC/IP/Port filtering rules in system

Current MAC/IP/ Port filtering rules in the system are listed here. Click

【

Delete Selected

】

delete selected rule.

Содержание UC510




















































































Результаты поиска

Содержание UC510

Отзывы:

Zycoo UC510, Руководство пользователя, Страница: 72 / 84

Результаты поиска

Содержание UC510

Отзывы: