Zoom NUD360-F Скачать руководство пользователя страница 42

Страница: 42 / 108

Software User’s Manual Ver.A1D-502-V8.03.30-NB

Video & Audio

The section Video & Audio provides the options to adjust the video

quality, configure the streaming details of the camera, and audio settings (for Audio supported

cameras only), which will be described in the succeeding pages.

The default settings of the camera are sufficient for most environments and the video

adjustments are not necessary. The following sections explain the ways to configure the video

quality or streaming details in case it is required to do so.

The [+] mark before Video indicates that the list can be expanded by clicking on it. Once

expanded, the list can later be collapsed again by clicking on the [-] mark.

5-6-1 Camera Options

In general, the Camera Options submenu allows users to set the

Line Frequency, Mounting Type, Video Application Mode, High Frame Mode, and

Rotation properties of the camera. Depending on the camera type, the parameters on the

Camera Options screen may vary.

Содержание NUD360-F













































































































Результаты поиска

Содержание NUD360-F

Отзывы:

Zoom NUD360-F, Руководство пользователя программного обеспечения, Страница: 42 / 108

Результаты поиска

Содержание NUD360-F

Отзывы: