Zeiss Axioscope 7 Скачать руководство пользователя страница 89

Страница: 89 / 140

OPERATION

Axioscope 5/7/Vario

Illumination and contrast methods in transmitted light …

ZEISS

03/2018

430035-7344-001

(4) Adjusting the height stop on the

condenser carrier

•

Loosen the setscrew (

625H

Fig. 4-4/

) on the height

stop with the Allen wrench (AF 3).

•

Focus the sample with the focusing drive.

•

Close the field diaphragm and adjust the
condenser vertically (

626H

Fig. 4-4/

) until you get a

sharp image.

•

Perform the vertical adjustment on the

condenser by small increments only to avoid

lifting out the sample.

•

Tighten the setscrew (

627H

Fig. 4-4/

) on the height

stop.

(5) Adjusting the height stop on the focusing

drive

•

Turn the clamping lever (

628H

Fig. 4-5/

) of the stop

towards the pin stop.

•

Move the stage with the aid of the focusing
drive (

629H

Fig. 4-5/

) to the highest position

allowable without risking colliding with

specimen holder or objectives.

•

Now press the clamping lever down until the

stop engages again.

Fig. 4-4

Adjusting the height stop on the
condenser carrier

Fig. 4-5

Adjusting the height stop on the
focusing drive

Содержание Axioscope 7













































































































































Результаты поиска

Содержание Axioscope 7

Отзывы:

Zeiss Axioscope 7, Руководство по эксплуатации, Страница: 89 / 140

Результаты поиска

Содержание Axioscope 7

Отзывы: