manualshive.com logo in svg

Zeiss Axioscope 7, Руководство по эксплуатации, Страница: 12 / 140

Поделиться
Скачать
Zeiss Axioscope 7 Скачать руководство пользователя страница 12

 

INTRODUCTION 

 

ZEISS 

Notes on instrument safety 

Axioscope 5/7/Vario 

 

 
 

12 

430035-7344-001 

03/2018 

 

CAUTION

 

The immersion fluid Immersol 518 N

  is irritating  to the skin. Avoid any contact with skin, 

eyes  and clothes. Read the safety data sheets  on Immersol 518 N

, Immersol 518 F

  and 

Immersol W

 carefully. If skin contact occurs, wash off with lots of water and soap.  

 

If eye contact occurs, flush with water immediately for at least 5 minutes. Seek medical 

assistance if irritation continues. 

 

 

CAUTION

 

Dispose of immersion fluid Immersol 518 N

  appropriately: Do not allow to contaminate 

surface water or get into drains. 

 

 

CAUTION

 

For stands equipped with motorized focusing drives, there is a risk of fingers being crushed in 

the working area when the microscope stage is lowered. 

 

Do not reach into the area between the microscope stage/stage carrier/condenser carrier and 

the base of the stand while the stage is being lowered. 

 

 

ATTENTION

 

The manufacturer assumes no liability for any use of  the microscope, its assemblies or 

individual parts if these are used in in a manner or for any purpose other than those described 
in this operating manual. This also applies to any maintenance or repair work not performed 

by authorized maintenance and repair personnel.  Moreover, the warranty and any claims 
thereunder will be voided. 

 

 

ATTENTION 

Microscope lamps radiate a lot of heat which could damage the heat-sensitive fluorescence 
filters. Do not remove the heat protection filter when using a fluorescence filter; otherwise the 

fluorescence filter may not function properly. 

 

 

ATTENTION 

Dirt and dust may affect the microscope’s performance. Protect it by using a dust cover when 

it is not in use. Always make sure that the instrument is switched off before covering it up. 

 

 

ATTENTION 

Closing or covering the ventilation slits may result in heat accumulation which could damage 
the instrument and even start a fire. Ensure that the ventilation slits are always kept open, 

uncovered and clear. Do not insert or drop anything into them or let anything fall into them. 

 

Содержание Axioscope 7













































































































































Отзывы:

Нет отзывов