Zeiss Axioscope 7 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 140

Zeiss Axioscope 7 Скачать руководство пользователя страница 84

START-UP

ZEISS

Using the Light Manager function

Axioscope 5/7/Vario

84

430035-7344-001

03/2018

3.4

Using the Light Manager function

When turned on, the previous setting of the Light Manager will be restored.
The LM function is enabled automatically if the default factory settings are active.

Disable/enable the LM function

To disable the LM function proceed as follows:

•

Press one of the

Snap

buttons

and

the

Intensity/LM

knob simultaneously for at least 1.5 seconds.

The indicator light blinks GREEN / ORANGE / GREEN in sequence.

To enable the use of the LM function proceed as follows:

•

Press one of the

Snap

buttons

and

the

Intensity/LM

knob simultaneously for at least 1.5 seconds.

The indicator light blinks GREEN / GREEN / GREEN in sequences.

Save the light intensity using the LM function

•

Press the

Intensity/LM

knob for at least 1.5 seconds.

The currently set light intensity value will be saved. After it is saved, the active LED illuminator switches

off for 300 ms. The darkness in the eyepieces indicates the successful action of the Light Manager.

NOTE

If the Colibri 3 light source is connected, the Light Manager function is not available.

3.5

Default factory settings of the microscope

The default factory settings are:

−

Light Manager enabled

−

Light intensity set to initial minimum value

−

all configuration stored will be cleared

To reset the microscope to default factory settings, proceed as follows:

•

Press and hold down the

Intensity/LM

knob for 20 seconds.

While the knob is held down from 3 s to 20 s, the indicator light blinks in RED.
It blinks GREEN after 20 seconds. When the indicator stops blinking and remains GREEN, the reset to the

default factory setting is successful.

«
...
82
83
84
85
86
...
»

Содержание Axioscope 7













































































































































Отзывы:

Нет отзывов