manualshive.com logo in svg

Zeiss Axioscope 7, Руководство по эксплуатации, Страница: 11 / 140

Поделиться
Скачать
Zeiss Axioscope 7 Скачать руководство пользователя страница 11

 

INTRODUCTION 

Axioscope 5/7/Vario

 

Notes on instrument safety 

ZEISS 

 

 
 

03/2018 

430035-7344-001 

11 

 

CAUTION

 

Only authorized personnel are permitted to operate the instruments. The personnel must have 

been instructed about and be aware of the risks involved  in  using the microscope. The 

Axioscope is a precision instrument whose functionality  can easily be damaged or even 
destroyed when handled improperly. 

 

 

CAUTION

 

Operating the instrument in an area with a potentially explosive atmosphere is prohibited.  

It may be operated only on stable, non-flammable surfaces.   

Specimens must be disposed of appropriately in accordance with  applicable  statutory 
regulations and internal work instructions. 

 

 

CAUTION

 

Gas discharge lamps, such as the HBO 100, emit ultraviolet radiation which may cause injuries 

to your eyes and skin. Never look directly into the beam and avoid exposing your skin directly 
to the beam. Never operate the microscope without the necessary safety equipment (e.g. 

special damping filters or the fluorescence protection screen). Gas discharge lamps have a 

high internal pressure when hot. Never change the lamps while they are still hot and always 
use protective gloves and masks when changing them. 

 

 

CAUTION

 

Avoid any contact with the hot lamp case. Before you change a lamp, disconnect the 

instrument from the power supply and wait 15 minutes for the lamp to cool down. 

 

 

CAUTION

 

When the lamp module (e.g. Colibri 3) is equipped with appropriate LED modules, or when a 

white light source coupled by a fluid light conductor is used, ultraviolet radiation may leak 
which can cause injury to your eyes  and skin. Never look directly into the light and avoid 

exposing your skin directly to the light. Always use the appropriate safety equipment when 

operating the microscope. 

 

 

CAUTION

 

Never look into the light beam of the illumination equipment -  with or without optical 
instruments - not even if you just want to look at a specimen. Irreparable eye damage may 

occur! 

 

 

CAUTION

 

Do not hold any flammable or easily combustible materials into the light beam. 

 

Содержание Axioscope 7













































































































































Отзывы:

Нет отзывов