background image

Administrator’s Guide for W80 DECT IP Multi-Cell System

135

Packetization Time (PTime)

PTime is a measurement of the duration (in milliseconds) that how long the audio data in each RTP packet is sent
to the destination, and defines how much the network bandwidth is used for the RTP stream transfer. Before estab-
lishing a conversation, codec and ptime are negotiated through SIP signaling. The valid values of ptime range from
10 to 60, in increments of 10 milliseconds. The default ptime is 20ms. You can also disable the ptime negotiation.

Topics

Supported PTime of Audio Codec
PTime Configuration

Supported PTime of Audio Codec

The following table summarizes the valid values of ptime for each audio codec:

Codec

Packetization Time (Minimum)

Packetization Time (Maximum)

G722

10ms

40ms

PCMA

10ms

40ms

PCMU

10ms

40ms

G729

10ms

80ms

G726-16

10ms

30ms

G726-24

10ms

30ms

G726-32

10ms

30ms

G726-40

10ms

30ms

iLBC

20ms

30ms

opus

10ms

20ms

PTime Configuration

The following table lists the parameter you can use to configure the PTime.

Parameter

account.X.ptime

[1]

<MAC>.cfg

Description

It configures the ptime (in milliseconds) for the codec.

Permitted
Values

0

-Disabled

10

-10

20

-20

30

-30

40

-40

50

-50

Содержание W80





































































































































































































































































Отзывы: