Yealink W80 Скачать руководство пользователя страница 169

Страница: 169 / 260

Handset Customization

166

Warnings Display Configuration

The following table lists the parameter you can use to configure the warnings display.

Parameter

phone_setting.warnings_display.mode

<y0000000000xx>.cfg

Description

It enables or disables the phone to display warnings.

Permitted
Values

-Disabled

-Enabled

Default

Advisory Tones

Advisory tones are the acoustic signals of your handset, which inform you of different actions and states.

It is not applicable to DD phones.

You can configure the following advisory tones independently for each other:

Keypad Tone

: plays when you press any key of the keypad. For CP930W, you can only configure it by nav-

igating to

Menu

Settings

Basic Settings

Sound

Advisory Tones

Keypad Tone

Touch Tone

: plays when you tap the keys (except the off-hook key and the touch keypad). You can only con-

figure it by navigating to

Menu

Settings

Basic Settings

Sound

Advisory Tones

Touch Tone

. It is only

applicable to CP930W.

Confirmation

: plays when you save settings or place the handset in the charger cradle. For CP930W, you can

only configure it by navigating to

Menu

Settings

Basic Settings

Sound

Advisory Tones

Confirmation

Low Battery

: plays when battery capacity is low and the handset requires being charged. For CP930W, you can

only configure it by navigating to

Menu

Settings

Basic Settings

Sound

Advisory Tones

Low Battery

Topic

Advisory Tones Configuration

Advisory Tones Configuration

The following table lists the parameters you can use to configure the advisory tones.

Parameter

custom.handset.keypad_tone.enable

<y0000000000xx>.cfg

Description

It enables or disables the handset to play a tone when any key is pressed. For CP930W, it plays a
tone only when the touch keypad is tapped.

Note:

It will take effect on all handsets that are registered on the same system. It works only if “stat-

ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.

Permitted
Values

-1

-Do not modify the handset configuration (Keep the original configuration of the handset).

-Disabled

-Enabled

Default

-1

Supported
Devices

W59R, W53H, W56H, CP930W

Handset UI

W59R/W56H/W53H

OK > Settings > Audio > Advisory Tones > Keypad Tone

CP930W

Menu > Settings > Basic Settings > Sound > Advisory Tones

Содержание W80





































































































































































































































































Результаты поиска

Содержание W80

Отзывы:

Похожие инструкции для W80

Бренды по названию

Популярные бренды

Yealink W80, Руководство администратора

Результаты поиска

Содержание W80

Отзывы:

Похожие инструкции для W80

Бренды по названию

Популярные бренды