Yealink W80 Скачать руководство пользователя страница 143

Страница: 143 / 260

Audio Features

140

-R SIP INFO, DTMF digits are transmitted by RTP Events compliant to RFC 2833 and the

SIP INFO messages.

Default

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > DTMF Type

Parameter

account.X.dtmf.dtmf_payload

[1]

<MAC>.cfg

Description

It configures the value of DTMF payload.

Note

: It works only if “account.X.dtmf.type” is set to 1 (RFC2833) or 3 (R SIP INFO).

Permitted
Values

Integer from 96 to 127

Default

101

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > DTMF Payload Type (96~127)

Parameter

account.X.dtmf.info_type

[1]

<MAC>.cfg

Description

It configures the DTMF info type.

Note

: It works only if “account.X.dtmf.type” is set to 2 (SIP INFO) or 3 (R SIP INFO).

Permitted
Values

-DTMF-Relay

-DTMF

-Telephone-Event

Default

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > DTMF Info Type

Parameter

features.dtmf.repetition

<y0000000000xx>.cfg

Description

It configures the repetition times for the phone to send the end RTP Event packet during an active call.

Permitted
Values

1, 2 or 3

Default

Web UI

Features > General Information > DTMF Repetition

Parameter

features.dtmf.duration

[2]

<y0000000000xx>.cfg

Description

It configures the duration time (in milliseconds) for each digit when a sequence of DTMF tones is
played out automatically.

Note

: If the time interval between two DTMF digits is less than this value, two or more same DTMF

digits could be identified as one DTMF digit. This may cause the loss of one or more DTMF digits. For
example, 2662 may be identified as 262. If so, you can modify the value of this parameter to a little
lower than the default value.

Permitted
Values

Integer from 0 to

Default

100

Parameter

features.dtmf.volume

<y0000000000xx>.cfg

Содержание W80





































































































































































































































































Результаты поиска

Содержание W80

Отзывы:

Похожие инструкции для W80

Бренды по названию

Популярные бренды

Yealink W80, Руководство администратора

Результаты поиска

Содержание W80

Отзывы:

Похожие инструкции для W80

Бренды по названию

Популярные бренды