Yamaha VF200 Скачать руководство пользователя | Manualshive

Страница: 50 / 120

background image

Instruments and indicators

44

Stop the engine immediately and see page
101 of this manual to drain the water from the
fuel filter. Get back to the port soon and con-
sult a Yamaha dealer immediately.

NOTICE

ECM00911

Gasoline mixed with water could cause
damage to the engine.

Engine trouble-alert indicator

If the engine malfunctions while cruising, the
engine trouble-alert indicator will start to
blink. Get back to the port soon and consult
a Yamaha dealer immediately.

NOTICE

ECM00921

In such an event, the engine will not oper-
ate properly. Consult a Yamaha dealer im-

mediately.

Low battery voltage alert

If the battery voltage drops, the battery volt-
age value will start to blink.

Get back to the port soon if the low battery
voltage alert device has activated. For charg-
ing the battery, consult your Yamaha dealer.

Overheat-alert indicator

If the engine temperature rises too high while
cruising, the overheat-alert indicator will start
to blink, and the engine speed will automati-
cally decrease to about 2000–3500 r/min.

Stop the engine immediately if the buzzer
sounds and the overheat device has activat-
ed. Check the cooling water inlet for clog-
ging.

1. Water separator-alert indicator

1. Engine trouble-alert indicator

1

ZMU08413

1

ZMU08414

1. Battery voltage value

1. Overheat-alert indicator

1

ZMU08415

1

ZMU08416

6CB-9-3B-1E0.book 44 ページ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
48
49
50
51
52
...
»

Содержание VF200

























































































































Отзывы:

Нет отзывов

Похожие инструкции для VF200

Бренд: Digital Equipment Страницы: 98

Бренд: CompuLab Страницы: 31

Бренд: IBASE Technology Страницы: 93

Бренд: Gigabyte Страницы: 31

Бренд: ASROCK Страницы: 64

A320M PRO-VH PLUS

Бренд: MSI Страницы: 154

Fatality H97 Killer series

Бренд: ASROCK Страницы: 109

Бренд: kobi Страницы: 24

EVAL-AD7625FMCZ

Бренд: Analog Devices Страницы: 28

Бренд: Micrel Страницы: 6

Бренд: Micrel Страницы: 10

Бренд: Micrel Страницы: 25

Бренд: Micrel Страницы: 28

Бренд: Altera Страницы: 6

Бренд: Kaba Страницы: 44

Бренд: Abit Страницы: 102

Бренд: Abit Страницы: 103

Бренд: Abit Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды