manualshive.com logo in svg

Yamaha VF200, Руководство пользователя

Поделиться
Скачать
Yamaha VF200 Скачать руководство пользователя страница 101

Maintenance

95

10. Install the cooling water inlet covers on

both sides of the gear case, and then
tighten the bolt to the specified torque.

EMU41137

Inspecting and replacing anodes

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales
from the surfaces of the anodes. Consult a
Yamaha dealer for replacement of external
anodes.

NOTICE

ECM00721

Do not paint anodes, as this would render
them ineffective.

TIP:

Consult a Yamaha dealer for inspecting and
replacement of internal anodes attached to
the engine.

VF200LA, VF225LA, VF250LA

VF250XA

VF250XA

EMU43971

Inspecting the battery

WARNING

EWM01903

Battery electrolyte is poisonous and
caustic, and batteries generate explosive
hydrogen gas. When working near the
battery:

Wear protective eye gear and rubber
gloves.

Do not smoke or bring any other source
of ignition near the battery.

The procedure for inspecting the battery var-
ies for different batteries. This procedure
contains typical inspections that apply to
many batteries, but you should always refer

Tightening torque:

7 N·m (0.71 kgf·m, 5.2 lb·ft)

Tightening torque:

2.0 N·m (0.20 kgf·m, 1.5 lb·ft)

1. Anode

1

ZMU06959

1. Anode

1. Anode

1

ZMU08317

1

ZMU07194

6CB-9-3B-1E0.book  95 ページ  ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды