Yamaha VF200 Скачать руководство пользователя

Страница: 60 / 120

Operation

3. Insert the oil dipstick completely and re-

move it again.

4. Check that the oil level on the oil dipstick

is between the upper and lower marks.
Consult your Yamaha dealer if the oil
level is not at the proper level or if it ap-
pears milky or dirty.

EMU40412

Outboard motor



Check that the outboard motor is mounted
properly and check the outboard motor
mounting bolts for looseness.



Check the propeller for damage.



Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out
and the engine can overheat during oper-
ation.

[ECM01802]

EMU40752

Installing top cowling

1. Check the rubber seal for damage. If the

rubber seal is damaged, have it replaced
by a Yamaha dealer.

1. Oil dipstick

1. Oil dipstick
2. Upper mark
3. Lower mark

ZMU06917

ZMU0691

1. Flushing device
2. Garden hose connector
3. Fitting

1. Rubber seal
2. Bottom cowling

ZMU06919

ZMU0697

6CB-9-3B-1E0.book 54 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Yamaha VF200, Руководство пользователя

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды