manualshive.com logo in svg

Yamaha VF200, Руководство пользователя

Поделиться
Скачать
Yamaha VF200 Скачать руководство пользователя страница 108

Trouble Recovery

102

Consult your Yamaha dealer if the new fuse
immediately blows again.

EMU40984

Power trim and tilt unit will not 
operate

WARNING

EWM02331

Never get under the engine while it is tilt-
ed. Severe injury could occur if the out-

board motor accidentally falls.

If the outboard motor cannot be tilted up or
down using the power trim and tilt unit be-
cause of a discharged battery or a failure
with the power trim and tilt unit, the outboard
motor can be tilted manually.
1. Stop the engine.
2. Loosen the manual valve screw by turn-

ing it counterclockwise until it stops.

VF200LA, VF225LA, VF250LA

VF250XA

3. Tilt the outboard motor up manually to

the desired position, and then tighten the
manual valve screw by turning it clock-
wise.

5. Fuel feed pump fuse (10 A)
6. Electric throttle valve fuse (10 A)
7. Main switch / PTT switch fuse (20 A)
8. Main fuse (60 A)

1. Fuse box cover
2. Fuse puller
3. Spare fuse (10 A, 15 A, 20 A, 30 A)
4. Spare main fuse (60 A)

1. Fuse puller

ZMU08319

1

2

3

4

ZMU08320

1

1. Manual valve screw

1. Manual valve screw

1

ZMU06962

1

ZMU07196

6CB-9-3B-1E0.book  102 ページ  ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды