Yamaha VF200 страница 94 Скачать руководство пользователя

Страница: 94 / 120

Maintenance

level measurement will be incorrect.

16. Recheck the oil level using the dipstick

to be sure the level falls between the up-
per and lower marks. Consult your
Yamaha dealer if the oil level is out of
specified level.

17. Start the engine and make sure that the

low oil pressure-alert indicator remains
off. Also, make sure that there are no oil
leaks.

NOTICE:

If the low oil pressure-

alert indicator comes on or if there
are oil leaks, stop the engine and find
the cause. Continued operation with
a problem could cause severe engine
damage. Consult your Yamaha dealer
if the problem cannot be located and
corrected.

[ECM01623]

18. Install the apron on the starboard side as

shown in the illustration.

VF200LA, VF225LA, VF250LA

VF250XA

19. Apply LOCTITE 572 to the threads of the

bolts and then install the bolts.

1. Oil dipstick
2. Upper mark
3. Lower mark

ZMU0691

1. Apron

ZMU07966

ZMU07960

6CB-9-3B-1E0.book 88 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Yamaha VF200, Руководство пользователя

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды