Yamaha VF200 Скачать руководство пользователя | Manualshive

Страница: 45 / 120

background image

Instruments and indicators

39

10-minute display will begin blinking.

5. Push the “

” (mode) button until the

desired 10-minute value is displayed.

6. Push the “

” (set) button again. The 1-

minute display will begin blinking.

7. Push the “

” (mode) button until the

desired 1-minute value is displayed.

8. Push the “

” (set) button again to start

the clock.

The clock operates on battery power. Dis-
connecting the battery will stop the clock.
Reset the clock after connecting the battery.

EMU36081

Voltmeter

The voltmeter displays the charge of the bat-
tery in volts(V).

EMU26723

Fuel level-alert indicator

If the fuel level decreases to one segment,
the fuel level alert segment will blink.
Do not continue to operate the engine at full
throttle if an alert device has activated. Get
back to the port using trolling engine speed.

NOTICE:

Running out of fuel can damage

the engine.

[ECM01771]

EMU26733

Low battery voltage-alert indicator

If battery voltage drops, the display will auto-
matically turn on and blink.
Get back to the port soon if an alert device
has activated. For charging the battery, con-
sult your Yamaha dealer.

EMU26742

Fuel management meter

The fuel management meter shows the state
of the fuel consumption while the engine is
running.

TRIP

TIME

BATT

km/h

knot

mph

km

mile

SPEED

YAMAHA

set

mode

ZMU07004

1. Fuel level-alert segment

1. Low battery indicator

TRIP

TIME

BATT

km/h

knot

mph

km

mile

SPEED

YAMAHA

set

mode

ZMU07005

1

TRIP

TIME

BATT

km/h

knot

mph

km

mile

SPEED

YAMAHA

set

mode

ZMU07006

1

6CB-9-3B-1E0.book 39 ページ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
43
44
45
46
47
...
»

Содержание VF200

























































































































Отзывы:

Нет отзывов

Похожие инструкции для VF200

Бренд: ASROCK Страницы: 128

ADRF5515A-EVALZ

Бренд: Analog Devices Страницы: 9

B450M MORTAR TITANIUM

Бренд: MSI Страницы: 144

Бренд: MSI Страницы: 104

Бренд: AKM Страницы: 30

Бренд: JETWAY Страницы: 52

Бренд: Microchip Technology Страницы: 31

Бренд: EVGA Страницы: 2

Бренд: Tadao Страницы: 3

Бренд: Intel Страницы: 74

Бренд: Epcom Страницы: 8

GA-H170M-HD3 DDR3

Бренд: Gigabyte Страницы: 44

Бренд: Erreka Страницы: 4

STEVAL-LLL002V1

Бренд: STMicroelectronics Страницы: 29

Бренд: Microchip Technology Страницы: 54

S2257 THUNDER 2400

Бренд: TYAN Страницы: 105

Бренд: Texas Instruments Страницы: 14

Бренд: Biostar Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды