Yamaha VF200 страница 36 Скачать руководство пользователя | Manualshive

Страница: 36 / 120

background image

Components

30

move the remote control lever, which
could result in an accident.

[EWM02581]

3. Install the cap.

EMU25996

Engine shut-off cord (lanyard) and
clip

The clip must be attached to the engine shut-
off switch for the engine to run. The cord
should be attached to a secure place on the
operator’s clothing, or arm or leg. Should the
operator fall overboard or leave the helm, the
cord will pull out the clip, stopping ignition to
the engine. This will prevent the boat from
running away under power.

WARNING! At-

tach the engine shut-off cord to a secure
place on your clothing, or your arm or leg
while operating. Do not attach the cord to

clothing that could tear loose. Do not
route the cord where it could become en-
tangled, preventing it from functioning.
Avoid accidentally pulling the cord dur-
ing normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power, the
boat could slow rapidly. This could cause
people and objects in the boat to be
thrown forward.

[EWM00123]

1. Throttle friction adjuster

1. Throttle friction adjuster

ZMU07026

1

ZMU069

8

9

1

1. Engine shut-off cord (lanyard)
2. Clip
3. Engine shut-off switch

1. Engine shut-off cord (lanyard)
2. Clip
3. Engine shut-off switch

ZMU07027

3

2

1

ZMU07043

1

2

3

6CB-9-3B-1E0.book 30 ページ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
34
35
36
37
38
...
»

Содержание VF200

























































































































Отзывы:

Нет отзывов

Похожие инструкции для VF200

Бренд: V2 ELETTRONICA Страницы: 12

Бренд: QDI Страницы: 69

phyBOARD-Subra-i.MX6

Бренд: Phytec Страницы: 2

Бренд: AOpen Страницы: 105

Бренд: JETWAY Страницы: 48

Бренд: Gigabyte Страницы: 136

Бренд: Aaeon Страницы: 50

Бренд: Emcore Страницы: 12

PCAN-MicroMod Evaluation Kit

Бренд: Peak Страницы: 18

tKINO-AL-E1-R10

Бренд: IEI Technology Страницы: 12

Бренд: H-Tec Страницы: 28

Бренд: Gigabyte Страницы: 18

xPico Wi-Fi Series

Бренд: Lantronix Страницы: 29

Бренд: Wolfson Страницы: 46

Бренд: TYAN Страницы: 59

Бренд: AMI Страницы: 47

Бренд: Intel Страницы: 86

Бренд: GVC Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды