Yamaha VF200 страница 35 Скачать руководство пользователя

Страница: 35 / 120

Components

ther forward or reverse, push the free accel-
erator button and move the remote control
lever.

TIP:



The free accelerator button can only be
pushed when the remote control lever is in
the neutral position.



After the button is pushed, the throttle be-
gins to open after the remote control lever
is moved at least 35





After using the free accelerator, return the
remote control lever to the neutral position.
The free accelerator button will return au-

tomatically to its set position. The remote
control will then engage forward and re-
verse normally.

EMU40606

Throttle friction adjuster

The throttle friction adjuster can be used to
adjust the resistance to movement of the re-
mote control lever, and can be set according
to operator preference. Adjust the throttle
friction according to the following procedure.
1. Remove the cap.

2. To increase resistance, turn the adjuster

clockwise. To decrease resistance, turn
the adjuster counterclockwise.

WARNING! Do not overtighten the
friction adjuster. If there is too much
resistance, it could be difficult to

1. Free accelerator button
2. Fully closed
3. Fully open

ZMU0702

35˚

ZMU06903

1. Cap

ZMU07025

ZMU06904

6CB-9-3B-1E0.book 29 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Yamaha VF200, Руководство пользователя

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды