Yamaha VF200 страница 100 Скачать руководство пользователя

Страница: 100 / 120

Maintenance

VF250XA

6. Remove any metal particles on the mag-

netic gear oil drain screw.

NOTICE:

there is an excessive quantity of met-
al particles on the magnetic gear oil
drain screw, this can indicate lower
unit problem. Consult your Yamaha
dealer.

[ECM01901]

7. Place the outboard motor in a vertical

position. Using a flexible or pressurized
filling device, inject the gear oil into the
gear oil drain screw hole.

VF200LA, VF225LA, VF250LA

VF250XA

8. Put a new gasket on the oil level plug.

When the gear oil begins to flow out of
the oil level plug hole, insert and tighten
the oil level plug to the specified torque.

TIP:

Apply a light coat of gear oil to the oil level
plug thread and gasket before installation.

9. Put a new gasket on the gear oil drain

screw. Insert and tighten the gear oil
drain screw to the specified torque.

TIP:

Apply a light coat of gear oil to the gear oil
drain screw thread and gasket before instal-
lation.

1. Oil level plug
2. Gasket

Recommended gear oil:

Yamalube Marine Gearcase Lube HD

or Hypoid gear oil

Recommended gear oil grade:

SAE 90 API GL-4 / SAE 80W API GL-5 /

SAE 90 API GL-5

Gear oil quantity:

1.040 L (1.099 US qt, 0.915 Imp.qt)

ZMU07191

Tightening torque:

7 N·m (0.71 kgf·m, 5.2 lb·ft)

ZMU06958

ZMU07192

6CB-9-3B-1E0.book 94 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Yamaha VF200, Руководство пользователя

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды