Yamaha VF200 страница 109 Скачать руководство пользователя

Страница: 109 / 120

Trouble Recovery

103

EMU46590

Water separator-alert is activated
after leaving port

WARNING

EWM01501

Gasoline is highly flammable, and its va-
pors are flammable and explosive.



Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.



There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.



This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.



The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

If the water separator-alert indicator blinks or
the buzzer sounds intermittently, perform the
following procedure.

TIP:

The buzzer sounds only when the remote
control lever is placed in neutral.

1. Stop the engine.
2. Remove the top cowling.
3. Remove the bolts, and then remove the

fuel filter cover.

4. Disconnect the water detection switch

coupler.

NOTICE:

Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-

1. Water separator-alert indicator

ZMU05441

1. Bolt
2. Fuel filter cover

ZMU06297

ZMU07012

ZMU07519

6CB-9-3B-1E0.book 103 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Yamaha VF200, Руководство пользователя

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды