Yamaha VF200 страница 76 Скачать руководство пользователя

Страница: 76 / 120

Operation

EMU40712

Procedure for shallow water cruising

1. Move the remote control lever to the

neutral position.

2. Push the “

” (up) side of the power trim

and tilt switch to tilt the outboard motor
up slightly to the desired position.

WARNING! Using the power trim and
tilt switch on the bottom cowling

while the boat is moving or engine is
on could increase the risk of falling
overboard and could distract the op-
erator, increasing the risk of collision
with another boat or an obstacle.

[EWM01851]

3. To return the outboard motor to the nor-

mal running position, push the “

”

(down) side of the power trim and tilt
switch to tilt the outboard motor down
slowly.

EMU28196

Cruising in other conditions

Cruising in salt water

After operating in salt water, flush the cooling
water passages with fresh water to prevent
them from becoming clogged. Also rinse the

1. Cooling water inlet

ZMU06942

ZMU07034

ZMU06926

1. Power trim and tilt switch

ZMU069

6CB-9-3B-1E0.book 70 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Yamaha VF200, Руководство пользователя

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды