Yamaha VF200 страница 107 Скачать руководство пользователя

Страница: 107 / 120

Trouble Recovery

101

Q. Are outboard motor mounting bolts loose?
A. Tighten bolts or have serviced by a
Yamaha dealer.

Q. Is steering pivot loose or damaged?
A. Have serviced by a Yamaha dealer.

EMU29434

Temporary action in

emergency

EMU29442

Impact damage

WARNING

EWM00871

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

1. Stop the engine immediately.
2. Check the control system and all compo-

nents for damage. Also, check the boat
for damage.

3. Whether damage is found or not, return

to the nearest harbor slowly and careful-
ly.

4. Have a Yamaha dealer check the out-

board motor before operating it again.

EMU46602

Replacing fuse

WARNING

EWM00632

Substituting an incorrect fuse or a piece
of wire could allow excessive current
flow. This could cause electric system
damage and a fire hazard.

If a fuse has blown, replace the fuse accord-
ing to the following procedure.
1. Turn the main switch to the “

” (off)

position.

2. Remove the fuse box cover.
3. Remove the fuse with a fuse puller, and

then replace it with a spare one of the
proper amperage.

ZMU06999

1. Fuse box cover
2. Ignition coil / Fuel injector / Variable cam-
shaft timing / ECM (Electronic Control Module)
fuse (30 A)
3. Starter relay fuse (30 A)
4. Fuel pump fuse (15 A)

ZMU08318

6CB-9-3B-1E0.book 101 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Содержание VF200

























































































































Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды

Yamaha VF200, Руководство пользователя

Результаты поиска

Содержание VF200

Отзывы:

Похожие инструкции для VF200

Бренды по названию

Популярные бренды