Yamaha EK40G Скачать руководство пользователя

Страница: 191 / 200

6H95G11

9-4

Power unit

Compression pressure

Consult this chart after the ignition and fuel systems have been checked.

Measure the compression
pressure.

Add a small amount of engine oil
into the cylinder through the
spark plug hole.

Check the piston, piston rings,
and cylinder bore for wear or
damage. Correct or replace if
worn or damaged.

Check the cylinder head gasket
and cylinder head for wear or
damage.
Replace if worn or damaged.

Does the
pressure exceed
the specification
values?

Yes

Check other component again.

Does the
compression
pressure
increase?

Yes

NOTE:

While restoring a damaged part, it is also necessary to trace and solve the cause of the damage.

6H95G11_09 04.7.5 11:53 Page 5

Содержание EK40G









































































































































































































Результаты поиска

Содержание EK40G

Отзывы:

Похожие инструкции для EK40G

Бренды по названию

Популярные бренды

Yamaha EK40G, Руководство по обслуживанию

Результаты поиска

Содержание EK40G

Отзывы:

Похожие инструкции для EK40G

Бренды по названию

Популярные бренды