Yamaha EK40G страница 138 Скачать руководство пользователя

Страница: 138 / 200

LOWR

6-39

6H95G11

Lower unit

Disassembling the lower case

Remove the taper roller bearing outer
race and shim(s).

NOTE:

Install the claws

as shown.

Remove the drive shaft bearing outer
race, shim(s), and drive shaft sleeve.

NOTE:

Install the claws as shown.

Remove the needle bearing.

Checking the pinion and forward
gear

Check the teeth of the pinion, and the
teeth and dogs of the forward gear for
cracks or wear. Replace if necessary.

Checking the bearings

Check the bearings for pitting or rum-
bling. Replace if necessary.

Checking the drive shaft

Check the drive shaft for bends or wear.
Replace if necessary.

Measure the drive shaft runout.

Checking the lower case

Check the skeg and torpedo for cracks or
damage. Replace the lower case if nec-
essary.

6F660230

6F660260

Bearing outer race puller
assembly

:90890-06523

Needle bearing attachment

90890-06614

Driver rod L3

: 90890-06652

Stopper guide plate

90890-06501

Stopper guide stand

90890-06538

Bearing puller assembly

90890-06535

Runout limit: 0.5 mm (0.020 in)

6H95G11_06 04.8.11 13:01 Page 42

Содержание EK40G









































































































































































































Результаты поиска

Содержание EK40G

Отзывы:

Похожие инструкции для EK40G

Бренды по названию

Популярные бренды

Yamaha EK40G, Руководство по обслуживанию

Результаты поиска

Содержание EK40G

Отзывы:

Похожие инструкции для EK40G

Бренды по названию

Популярные бренды