manualshive.com logo in svg

Yamaha EK40G, Руководство по обслуживанию

Поделиться
Скачать
Yamaha EK40G Скачать руководство пользователя страница 120

NOTE:

When installing the pump housing, apply
grease to the inside of the housing, and then
turn the drive shaft clockwise while pushing
down the pump housing.

Installing the lower unit

1.

Set the gear shift to the reverse position
at the lower unit. Make sure that the shift
rod is in the reverse position.

2.

Screw in the locknut 

1

completely.

3.

Install the two dowels 

2

into the lower

unit.

4.

Install the lower unit into the upper case,
and then tighten the lower case mounting
bolts 

3

to the specified torque.

5.

Connect the shift rod. 

NOTE:

Screw the adjusting nut 

4

down until it light-

ly seated, and then tighten the locknut.

LOWR

6-21

6H95G11

Lower unit

Lower case mounting bolt 

3

:

21 N·m (2.1 kgf·m, 15.5 ft·lb)

4.

Align the groove in the impeller 

9

with

the Woodruff key 

0

, and then install the

impeller onto the drive shaft.

5.

Install the insert cartridge 

q

into the

pump housing 

w

, and then apply grease

to the inside of the insert cartridge.

NOTE:

Align the insert cartridge projection 

a

with

the hole 

b

in the pump housing.

6.

Install the seal 

e

, a new gasket 

r

, and

pump housing assembly 

t

into the lower

case, tighten the bolts 

y

.

6F660370

9

0

6F660380

q

w

b

a

r

t

y

y

e

6F660395

6H960830

2

3

2

1

4

 6H95G11_06  04.8.6 9:32  Page 24

Содержание EK40G









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды