Yamaha EK40G Скачать руководство пользователя

Страница: 139 / 200

6H95G11

6-40

Drive shaft and lower case

Assembling the oil seal housing

Apply grease to new oil seals, and then
install them into the oil seal housing.

Assembling the lower case

Install the needle bearing into the lower
case to the specified depth.

NOTE:

Install the needle bearing with the manufac-
ture identification mark

facing up.

Be careful not to let the stopper

get out

of position when using the driver rod SL.

Install the sleeve, original shim(s), and
drive shaft bearing outer race.

Add or remove shim(s), if necessary, if
replacing the pinion or lower case.

NOTE:

Apply gear oil to the inside and outside of
the sleeve before installation.

Install the sleeve with the projection

fac-

ing forward.

Install the original shim(s) and taper roller
bearing outer race.

Add or remove shim(s), if necessary, if
replacing the forward gear or lower case.

6F660270

6B460350

6F660290

Ball bearing attachment

90890-06653

Driver rod L3

: 90890-06652

Bearing outer race attachment

90890-06627

Driver rod LS

: 90890-06606

Bearing outer race attachment

90890-06622

Driver rod LL

: 90890-06605

Driver rod SL

: 90890-06602

Needle bearing attachment

90890-06614

Bearing depth plate

: 90890-06603

Depth

182.5 — 183.0 mm
(7.19 — 7.20 in)

6H95G11_06 04.8.11 13:01 Page 43

Содержание EK40G









































































































































































































Результаты поиска

Содержание EK40G

Отзывы:

Похожие инструкции для EK40G

Бренды по названию

Популярные бренды

Yamaha EK40G, Руководство по обслуживанию

Результаты поиска

Содержание EK40G

Отзывы:

Похожие инструкции для EK40G

Бренды по названию

Популярные бренды