Yamaha EK40G Скачать руководство пользователя страница 150

Страница: 150 / 200

LOWR

6-51

6H95G11

Lower unit

Slowly turn the drive shaft clockwise and
counterclockwise and measure the back-
lash when the drive shaft stops in each
direction.

Add or remove shim(s) if out of specifica-
tion.

M: Measurement

Remove the special service tools from
the propeller shaft.

Apply a load to the reverse gear by
installing the propeller

(without the

washer

), then the spacer

as shown.

NOTE:

Tighten the propeller nut

while turning the

drive shaft until the drive shaft can no longer
be turned.

Slowly turn the drive shaft clockwise and
counterclockwise and measure the back-
lash when the drive shaft stops in each
direction.

10. Add or remove the shim(s) if out of spec-

ification.

M: Measurement

11. Remove the special service tools, and

then install the water pump assembly.

Forward gear backlash:

0.19– 0.47 mm (0.0075– 0.0185 in)

Reverse gear backlash:

0.76– 1.04 mm
(0.0299– 0.0409 in)

Forward gear

Shim thickness

backlash

Less than

To be decreased by

0.19 mm (0.0075 in)

(0.33 - M)

0.53

More than

To be increased by

0.47 mm (0.0185 in)

(M - 0.33)

0.53

Available shim thicknesses:

0.05, 0.08, 0.12, 0.30, and
0.50 mm

Available shim thicknesses:

0.05, 0.08, 0.12, 0.30, and
0.50 mm

6F660560

Reverse gear

Shim thickness

backlash

Less than

To be increased by

0.76 mm (0.0299 in)

(0.9 - M)

0.53

More than

To be decreased by

1.04 mm (0.0409 in)

(M - 0.9)

0.53

6H95G11_06 04.8.11 13:01 Page 54

Содержание EK40G









































































































































































































Результаты поиска

Содержание EK40G

Отзывы:

Бренды по названию

Популярные бренды

Yamaha EK40G, Руководство по обслуживанию

Результаты поиска

Содержание EK40G

Отзывы:

Бренды по названию

Популярные бренды