Yamaha EK40G страница 188 Скачать руководство пользователя | Manualshive

Страница: 188 / 200

background image

TRBL

SHTG

9-1

6H95G11

TRBL

SHTG

Troubleshooting

NOTE:

9

To diagnose a mechanical malfunction, use the troubleshooting charts pertaining to the trouble
located in this chapter. Also, when checking and maintaining the outboard motor, see Chapters
4–8 for safe maintenance procedures.

9

Check that all electrical connections are tight and free from corrosion.

Power unit

Symptom: Manual starter turns and or starter motor operate but engine will not
start.

9

Check the ignition system, fuel system, and the compression pressure as listed below.

9

Be sure the air vent screw on the fuel tank is open.

Ignition system

Check the engine stop lanyard
switch and or engine stop button
for continuity (with clip installed).

Check the condition of the spark
plugs.

Check the ignition spark using
the spark gap tester.

Replace the engine stop lanyard
switch and or engine stop button.

Is there correct?

(continued on following page)

Yes

Yes

No

Clean and replace as required.

No

Check the spark plug wires or caps
for deterioration and damage.

No

Yes

Are they in
good condition?

Is a good spark
being produced?

Measure the ignition coil
resistance.

Replace the ignition coil or caps
as necessary.

Yes

Replace the ignition coil.

No

No

Is resistance
within
specification?

Is there any
deterioration or
damage?

Yes

w

9

Do not touch any of the con-
nections of the spark gap
tester leads.

9

Do not let sparks leak out of
the removed spark plug
caps.

9

Keep flammable gas or liq-
uids away, since this test
can produce sparks.

6H95G11_09 04.7.5 11:53 Page 2

«
...
186
187
188
189
190
...
»

Содержание EK40G









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EK40G

Бренд: E-peas Страницы: 2

Бренд: Qorvo Страницы: 8

Бренд: Texas Instruments Страницы: 8

Бренд: Micrel Страницы: 14

EZ-USB HX2LP CY4606

Бренд: Cypress Страницы: 2

Бренд: Freescale Semiconductor Страницы: 16

Бренд: BCM Страницы: 3

TB360-BTC PRO 2.0

Бренд: Biostar Страницы: 59

Бренд: Merit Страницы: 4

Бренд: NXP Semiconductors Страницы: 35

Бренд: Supermicro Страницы: 95

STEVAL-LLL002V1

Бренд: STMicroelectronics Страницы: 29

Бренд: MSI Страницы: 87

Бренд: ComNav Technology Страницы: 28

Бренд: unicore Страницы: 11

Desktop Board D850EMD2

Бренд: Intel Страницы: 24

Бренд: Zeal-All Страницы: 10

Бренд: Zeal-All Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды