Yamaha EK40G Скачать руководство пользователя страница 148

Страница: 148 / 200

Example:
If “M1” is 25.30 mm and “F” is (+4), then

T1 = 25.70 + (+4)/100 – 25.30 mm
= 25.70 + 0.04 – 25.30 mm
= 0.44 mm

Select the forward gear shim(s) (T1) as
follows.

Example:
If “T1” is 0.44 mm, then the forward gear
shim is 0.42 mm.
If “T1” is 0.50 mm, then the forward gear
shim is 0.48 mm.

Selecting the reverse gear shims

Install the ball bearing onto the propeller
shaft housing.

Measure the bearing housing height (M2)
as shown.

LOWR

6-49

6H95G11

Lower unit

6F660510

NOTE:

Select the shim thickness (T2) by using the
specified measurement(s) and the calcula-
tion formula.

Measure the bearing housing at three
points to find the height average.

Calculate the reverse gear shim thick-
ness (T2) as shown in the examples
below.

NOTE:

“R” is the deviation of the lower case dimen-
sion from standard. The “R” mark

stamped on the trim tab mounting surface of
the lower case in 0.01 mm units. If the “R”
mark is unreadable, assume that “R” is zero
and check the backlash when the unit is
assembled.

Calculation formula:

Forward gear shim thickness (T1) =
25.70 + F/100 – M1

Available shim thicknesses:

0.05, 0.08, 0.12, 0.30, and
0.50 mm

Calculated numeral

Rounded numeral

at 1/100th place

1, 2

3, 4, 5

6, 7, 8

9, 10

6F660520

Shimming plate

: 90890-06701

Digital caliper

: 90890-06704

R+2

6F660530

6H95G11_06 04.8.11 13:01 Page 52

Содержание EK40G









































































































































































































Результаты поиска

Содержание EK40G

Отзывы:

Бренды по названию

Популярные бренды

Yamaha EK40G, Руководство по обслуживанию

Результаты поиска

Содержание EK40G

Отзывы:

Бренды по названию

Популярные бренды